This parachute kit (launcher + parachute) is tailor-made for the DJI Inspire 1 but can also be used on other drones up to 4.9 kg. It reduces the impact energy to 66 Joules and thus complies with the regulations of certain countries, such as France, where the impact energy is limited to 69 Joules.
Folds and re-installs easily in less than a minute
Ultra-light carbon tube
Solid Kevlar lines
Lockable to avoid unintentional triggering during transport
This is the latest addition to Opale Paramodels line of drone parachutes. An innovative model, especially for its low weight and new ejection system. It comes with an installation kit that will allow you to simply mount it on an Inspire 1 DJI.
A simple and innovative technology
This new system ejects the parachute in a fraction of a second to a distance of 3 to 8 meters. This system has the particularity of not applying permanent pressure to the parachute, which guarantees safe ejection, ultra-fast deployments and reduced wear without the need to fold it up regularly.
The lines are made of aramid and kevlar which allows to support a load of 300 kg. The fixing straps and lines are designed so as not to make knots, which prevents tangling and extends their life span.
The parachute is also made of high quality materials. It uses the same materials as those used to manufacture parachutes for ultra-light motorized aircraft. To reduce friction and promote ejection, the parachute is coated with silicon, which also allows it to hold well over time. Nevertheless, it remains extremely light with its 32g/m2 (95 grams for the whole parachute).
Reduction of impact energy
This is often the main reason for using a parachute and is required by the regulations of some countries that impose a maximum impact force not to be exceeded. On this side, the ST60X does its job very well. It has a new generation parachute with a well thought-out geometry that allows it to slow down the fall while remaining stable (attenuation of the pendulum effect) while remaining ultra-light. The impact energy of a 4.9 kg drone in free fall equipped with this parachute is thus reduced to 66 Joules. This makes it possible to comply with certain regulations such as in France where the impact energy must be a maximum of 69 Joules.
Reliability and safety
A particular effort has been made on these two points and that is why the ST60X does not use a short-circuit fuse blow-out system. This eliminates the need for additional batteries and reduces the risk of fire. In the same concern of simplicity and safety, this system does not use any pyrotechnic system, which facilitates maintenance and avoids the risks associated with highly compressed gases. Finally, since the parachute is not under constant pressure, its lifespan is extended and its deployment is even faster.
Tube dimensions: 150x60mm / 5.9x2.4in
Total weight: 220gr
Servomotor connector: UNI
Signal: PWM compatible with a transmitter or a stand-alone module
Tension : 4.8 to 7.2v
Flat area: 1.8m2 / 19.4ft2
Lines : Dynema / Spliced Aramid Kevlar (no knot)
Fabrics: 32gr/m2 with silicon coating
Fixation strap Aramid 300daN (300kg / 661.4lb)
Indicative falling speed according to the total flight mass for a 1.8m2 (19.4ft2) parachute:
TOTAL MASS (IN KG / LBS):
1.5 / 3.3
2 / 4.4
2.5 / 5.5
3 / 6.6
3.5 / 7.7
4 / 8.8
4.5 / 9.9
4.9 / 10.8
Sink rate (in m/s):
Impact energy (in joules):
Included in this kit:
1 x Safetech ST60X ejection tube
1 x 1.8m2 parachute
1 x fixation strap
1 x servomotor
1 x hardware and accessories kit
1 x DJI Inspire 1 mounting kit
Required and not included:
Transmitter or stand-alone module
4.8 to 7.2V battery
Total system weight (in ounces)
Launcher diameter (in millimeters)
60mm / 2.4"
Parachute weight (in grams)
95g / 3.35oz
Launcher weight (in grams)
125g / 4.4oz
4.8V - 7.2V
Maximum aircraft weight (in kg)
4.9kg / 10.8lbs
Aircraft recommended weight range (in kilograms)
3.2kg / 7lbs
Parachute area (in m²)
Total system weight (in grams)
220g / 7.8oz
Nylon siliconized fabric specially made for parachutes
Opale parachute are compatible with Multirotor they unfolds on order in a split second to ensure a smooth landing after a maneuver much less smooth!
The container is attached to the parachute so that you can use it again immediately after a collapse.
Really compact and light, very strong and equipped with reinforcements such as those you find on a full size parachute, no doubt this is going to be the perfect friend for your crazy trips or more wisely to efficiently protect your onboard photo / video equipment. The great thing is that you can use it either on a model in the Opale Paramodels range or on a Multirotor.